Drukarnia.BLOG

Which Silicone Hardness Is Best for Customized Silicone Molds?

When you order customized silicone molds, one question comes up again and again: how soft or hard should the silicone be? If the mold is too soft, it may sag, stretch, or lose its shape. If it is too hard, it can be difficult to demold, or it may crack around fine details.

The good news is that you do not need to be an engineer to choose well. This guide explains silicone hardness in simple words, shows which range suits which project, and covers what to tell your silicone molds maker before production starts.

What Is Silicone Hardness?

Silicone hardness is measured with a tool called a durometer. The result is usually given on the Shore A scale, which runs from 0 to 100. A lower number means a softer, more flexible material. A higher number means a firmer one.

To picture it, a very low number feels like soft gel. Around Shore A 30 to 40 feels close to a rubber band or a soft eraser. Higher numbers, such as 60 to 70, feel more like a firm shoe sole. Extra-soft silicones are sometimes measured on a different scale called Shore 00, so always check which scale a supplier is using.

Why Hardness Matters for Customized Silicone Molds

Hardness changes how a mold behaves every time you use it. It affects:

  • Demolding: Softer molds peel away easily, which helps with deep shapes and undercuts.

  • Detail: Softer silicone bends into tiny lines and textures, so fine detail is easier to capture and release.

  • Shape stability: Harder molds hold their form better, which is useful for large or heavy pours.

  • Durability: Very soft silicone can tear sooner with rough use, while firmer silicone often handles repeated casting better.

In short, the right hardness is a balance between easy release and strong support.

Soft, Medium, or Hard: A Simple Guide

The ranges below are general starting points. Exact numbers vary between materials and suppliers.

Soft Silicone (About Shore A 10 to 25)

Soft silicone is best for detailed models, deep undercuts, fragile casts, and small pieces such as jewelry or miniatures. It peels away gently, so delicate parts are less likely to break.

The trade-off is that it can stretch or sag, and it may tear more easily with heavy materials. Large soft molds often need a support shell to keep their shape.

Medium Silicone (About Shore A 30 to 40)

This is the all-rounder. Medium hardness works well for resin, candles, soap, chocolate, and many craft projects. It is flexible enough for easy demolding and firm enough to keep its shape. If you are unsure, this range is usually the safest place to start.

Hard Silicone (About Shore A 50 to 70)

Hard silicone suits large, flat, or simple shapes and heavier materials such as plaster or concrete. It also works for higher-volume production where the mold must stay stable. The trade-off is that deep undercuts are harder to release, and very fine detail may not flex out as smoothly.

Best Hardness for Common Projects

Use these as starting points, not strict rules.

  • Epoxy resin art and jewelry: soft to medium, so small details and thin parts release cleanly.

  • Candles and soap: medium, which balances flexibility with enough support for the weight of wax or soap.

  • Chocolate, candy, and gummies: medium, using food grade silicone so the mold is safe for direct food contact.

  • Baking molds: often a little firmer, so the mold holds its shape when filled with batter.

  • Concrete and plaster: medium to hard, because heavy materials need a mold that does not bulge.

  • Miniatures and fine textures: soft, to capture and release tiny details.

If your project fits more than one group, share it with your silicone molds maker and ask for a recommendation based on your design.

Other Factors That Matter Besides Hardness

Hardness is only one part of the picture. Before you order customized silicone molds, also think about:

  • Tear strength: How well the silicone resists ripping when you pull it away from a cast.

  • Elongation: How far it can stretch before it breaks. This is important for undercuts.

  • Wall thickness: A thicker wall feels firmer, while a thin wall feels softer, even with the same silicone.

  • Mold size and shape: Large molds usually need more support than small ones.

  • Cure type: Platinum-cured silicone usually has low shrinkage and is common for food and skin-safe uses. Tin-cured silicone often costs less but may shrink more over time.

  • Temperature range: If you pour hot materials or bake, check the heat rating.

How Silicone Molds Manufacture Affects Final Hardness

The number on a data sheet is only useful if every mold in your order actually matches it. That depends on the quality of the silicone molds manufacture process.

Hardness is shaped by the silicone formula, the mixing ratio, the amount of catalyst, and the curing time and temperature. If the mix is uneven, you can end up with soft spots or a mold that does not cure fully. Good silicone mold manufacturing uses measured batching, controlled curing, and regular hardness checks with a durometer. Many makers also heat the finished mold again (post-curing) to make it more stable.

A reliable silicone molds maker will tell you the hardness they plan to use, test it on a sample, and be open about the material they choose. If a supplier cannot explain the hardness of their molds, that is worth questioning.

What to Tell Your Silicone Molds Maker

The more detail you give, the better the result. Before you request customized silicone molds, share these points:

  • What you will cast (resin, wax, soap, chocolate, plaster, or something else)

  • Pouring or baking temperature

  • How many times you expect to use each mold

  • How detailed the design is and whether it has undercuts

  • Whether the mold needs to be food safe

  • Size of the finished piece and the number of molds you need

  • Whether you want a sample first

With this information, the maker can suggest a hardness and design, instead of guessing.

Common Mistakes to Avoid

  • Choosing the hardness by price or by what a friend uses, without testing it on your own design.

  • Using very soft silicone for large, heavy casts without any support.

  • Picking hard silicone for a design with deep undercuts.

  • Skipping the sample stage and ordering in bulk right away.

  • Ignoring heat limits when pouring hot materials.

Frequently Asked Questions

What Shore A hardness is best for silicone molds?

There is no single best number. For general use, many people start with a medium range of about Shore A 30 to 40. Choose softer for fine detail and undercuts, and harder for large or heavy casts.

What is the difference between Shore A 20 and Shore A 40 silicone?

Shore A 20 is softer and more flexible, so it captures fine detail and peels easily, but it can stretch and tear more. Shore A 40 is firmer and holds its shape better, but it bends less around deep undercuts.

Is softer silicone better for resin molds?

Often yes, especially for small or detailed pieces, because soft silicone releases the cast with less force. For larger resin pieces, a medium hardness may give better support.

Can I change the hardness of a customized silicone mold after it is made?

No. Hardness is set when the silicone cures. If the mold is not right, you need a new mold, which is why testing a sample first is so helpful.

Does hardness affect how long a silicone mold lasts?

It can. Very soft molds may tear sooner with rough handling, while firmer molds can resist wear better. Care, material quality, and the type of material you cast also play a big role.

What hardness is best for food grade silicone molds?

Medium hardness works well for chocolate, candy, and gummies, while baking molds are often a little firmer. In every case, make sure the silicone is food grade and ask for test reports.

How can I find out the hardness of a silicone mold?

Check the product data sheet, ask your supplier, or measure it with a Shore A durometer. A trustworthy silicone molds maker can tell you the hardness of each material they use.

Final Thoughts

Choosing the right hardness for customized silicone molds comes down to your design, your casting material, and how often you plan to use the mold. Soft silicone suits fine detail, medium silicone suits most projects, and hard silicone suits large, heavy, or high-volume work.

When in doubt, describe your project to an experienced silicone molds maker, ask for a recommendation, and approve a sample before you place a bulk order. A little testing at the start can save a lot of time and cost later.

Articles about local business and interesting people:

Share your ideas in a new publication.
We are waiting for your longread!
RS

Rubber Silicone Molds

@rubbersiliconemolds

4Longreads
70Views
On Drukarnia since September 14

More from the author

You may also be interested in:

Comments (0)

Support the author first.
Write a comment!

You may also be interested in: